How to Set Up a Xbox 360 Wireless Controller on Your Xbox 360

Because there are so many sport games with Xbox 360, using a wireless controller would be much more convenient than using a controller connected to the Xbox 360 with wires. The wireless controller will give players more freedom to move when playing. When first using a wireless controller with an Xbox 360, whether the controller is brand-new or new to that particular console, it is necessary to set it up. This process is simple and straightforward to perform.

                    

Things You Need

Xbox 360

Xbox 360 wireless controller

Instructions

1. Turn on your Xbox 360.

2. Put in the batteries and power on the Xbox 360 wireless controller.

3. Press the “Connect” button on your Xbox 360 controller. Can not find the button? Just watch carefully and the button is between the charge port and the Left Bumper button. Once pressed, the LED on the “Xbox” button on your controller will start spinning.

4. After the LED on your controller begins to spin, press the “Connect” button located to the right of “Memory Unit B” on the Xbox 360 console immediately.

The LEDs on both the controller and the console flash, and the controller is assigned Player 1, 2, 3 or 4. If the controller is not assigned a player number, repeat the process.

Tips & Warnings

It doesn't really matter which connect button you press first. Just remember that you only have a limited amount of time to press both.

How to Use a Slingshot

No matter you're using a stick and rubber band or you've invested in a quality weapon, proper use of any slingshot is necessary for both accuracy and safety. Usually a slingshot is used for target shooting, but sometimes people also use it for hunting. Using a slingshot is an easy and inexpensive hobby and proper use will help you hit whatever your target may be. Article below will teach you how to use a slingshot.

                 

Things You Need

Eye protection

Slingshot

Ammunition

Instructions

1. The most important thing is to remember wearing eye protection at all times. The reason to wear the protection is that ammunition can ricochet off surrounding objects and come back at you.

2. Hold the handle of the slingshot firmly and either directly perpendicular or parallel (whichever you prefer) to the ground in your non-dominant hand. And you need to use your stronger hand to control the ammunition. Make sure the wrist brace is resting snugly on your forearm to help steady your shot if your slingshot has one.

3. Now you can choose your ammunition based on your needs. Any small solid object, like a rock or a BB, can be used. But you can buy slingshot ammunition of different sizes and weights in most hunting stores. Choose the type of ammunition suits your purpose best. Twitter. Even paintballs can be used as ammunition to leave marks on your target.

4. Place your ammunition in the center of the pouch of the slingshot. Then grip the ammunition with your thumb and first two fingers through the pouch. Pull this straight back as far as possible. Remember you won’t have much accuracy in your shot if you pull the ammunition.

5. The last step is to aim at the target and release the pouch and ammunition.

How to Replace a PSP Laser

Laser in your PSP is the most important part because it reads the game discs and allows them to be played on the device. So if the laser in your PSP is damaged or broken, your PSP will be completely worthless. However, you can fix the problem by yourself. You can easily open your PSP cover and replace the damaged laser. And you need to completely disassemble your PSP to access the laser.
                  

Things You Need
Small Phillips-head screwdriver
Instructions
1. Power off your PSP. Turn it over and take off the battery cover. Get the battery out of its compartment.
2. Remove the 4 screws from each corner of the battery compartment with the Phillips-head screwdriver. First to remove the 2 screws located on the top and bottom of the corners of the side of the unit. Then remove the one on the bottom of the unit.
3. Use your fingers or the plastic tool to pry the faceplate off the unit and set it aside.
4. Insert the tip of your Phillips-head screwdriver in the seam between the button bar and bottom of the LCD screen. Then, gently pry the button bar off the unit.
5. Use the tip of your screwdriver to pop the 4 tabs on each corner of the LCD screen, and then lift the screen up. Carefully take off the 2 screen cables from the back of the screen and set the screen aside.
6. There is a metal LCD plate covering the motherboard and you need to remove all 7 screws from it. Remove the LCD plate and set it aside.
7. Gently unplug the 2 large orange ribbon cables from the left side of the motherboard. Remove all screws from the sides of the motherboard with your screwdriver.
8. Lift the motherboard out of the unit and disconnect the white antenna wire from the corner of the board. Put the motherboard away.
9. Remove all screws from the metal motherboard support plate underneath where the motherboard used to sit, and then remove the plate itself.
10. Remove all screws from the sides of the memory stick circuit board and lift it out of the unit to expose the laser assembly door.
11. Pop the door up and reveal the metal laser assembly with the screwdriver’s tip.
12. You will find 4 screws on each corner of the square metal assembly. Use your screwdriver to remove them and then lift the square metal assembly out of the unit.
13. Remove all screws from the sides of the assembly and gently pull it apart.
14. Now you can remove the old broken assembly and replace with the new one. At last, reassemble your PSP in the reverse order you took it apart.

How you can Replace a PSP Laser

Laser within your PSP may be the most important part since it reads the game discs and permits them to become played on the device. So if the laser inside your PSP is damaged or broken, your PSP will be fully worthless. However, you are able to repair the issue by your self. You can effortlessly open your PSP cover and replace the damaged laser. And also you need to have to completely disassemble your PSP to access the laser.

Factors You require

Small Phillips-head screwdriver

Guidelines

1. Energy off your PSP. Turn it over and take off the battery cover. Get the battery out of its compartment.

2. Take away the 4 screws from every corner of the battery compartment using the Phillips-head screwdriver. Very first to take away the 2 screws positioned on the leading and bottom from the corners of the side in the unit. Then get rid of the one on the bottom on the unit.

3. Use your fingers or the plastic tool to pry the faceplate off the unit and set it aside.

4. Insert the tip of your Phillips-head screwdriver inside the seam amongst the button bar and bottom in the LCD screen. Then, gently pry the button bar off the unit.

5. Use the tip of your screwdriver to pop the 4 tabs on each and every corner in the LCD screen, and then lift the screen up. Very carefully take off the 2 screen cables from the back on the screen and set the screen aside.

6. There is a metal LCD plate covering the motherboard and you require to get rid of all 7 screws from it. Take away the LCD plate and set it aside.

7. Gently unplug the 2 big orange ribbon cables from the left side in the motherboard. Get rid of all screws in the sides on the motherboard together with your screwdriver.

8. Lift the motherboard out in the unit and disconnect the white antenna wire in the corner from the board. Place the motherboard away.

9. Get rid of all screws from the metal motherboard assistance plate underneath exactly where the motherboard employed to sit, and after that remove the plate itself.

10. Take away all screws in the sides of the memory stick circuit board and lift it out in the unit to expose the laser assembly door.

11. Pop the door up and reveal the metal laser assembly with all the screwdriver's tip.

12. You will find 4 screws on every corner on the square metal assembly. Use your screwdriver to eliminate them then lift the square metal assembly out from the unit.

13. Eliminate all screws in the sides from the assembly and gently pull it apart.

14. Now you'll be able to get rid of the old broken assembly and replace with all the new one. At last, reassemble your PSP within the reverse order you took it apart.